Differences

This shows you the differences between two versions of the page.

--- nodes:gb7win [2025/10/08 06:59] – m0mzf
+++ nodes:gb7win [2025/10/11 14:53] (current) – [Current and planned ports] m0mzf
@@ Line 19: / Line 19: @@
 |4| 70.4875MHz \\ 12.5KHz FM  | V Omni 0dBd 7mAGL   | - | -   | planned | | |
 |6| 50.650MHz \\ 12.5KHz FM  | V Omni 0dBd 40mAGL | 1011 QPSK 2k4 IL2P+CRC    | 13dBW 2.4KHz | active | [[nodes:gb7bdh|GB7BDH]] [[nodes:gb7rdg|GB7RDG]] |[[http://wessex.hopto.org:8070/|Wessex]] |
-|7| 432.650MHz \\ 25KHz FM  | V Omni 5dBd 7mAGL   | 0011 C4SK 9k6 IL2P+CRC | 14dBW 5KHz   | testing, low antenna | [[nodes:gb7sou|GB7SOU?]] | [[http://zepler-websdr.suws.org.uk/|SUWS]] |
+|7| 432.650MHz \\ 25KHz FM  | V Omni 5dBd 40mAGL   | 0010 GFSK 9k6 IL2P+CRC | 14dBW 5KHz   | testing | [[nodes:mb7npw|MB7NPW?]] | [[http://zepler-websdr.suws.org.uk/|SUWS]] |
 =====Coverage Maps=====
 Simulations from radiomobileonline; Outstation antenna 12m AGL; Strong signal 15dBuV/m, Weak Signal 3dBuV/m, Path "reliability" 95%
@@ Line 40: / Line 40: @@
 ====LinBPQ====
 **Version**
-<code>G8BPQ AX25 Packet Switch System Version 6.0.25.5 October 2025 (Test)</code>
+<code>G8BPQ AX25 Packet Switch System Version 6.0.25.6 October 2025 (Test)</code>
 **Last updated**
-<code>2025-09-08 07:59 BST</code>
+<code>2025-09-10 10:24 BST</code>
 **Global**
@@ Line 49: / Line 49: @@
 ; Set up some global  stuff
+; Set up some global  stuff
+;T3=540                 ; L2 validation timer - increase from default 180 (3min)
+;IDLETIME=2700          ; L2 idle link shutdown timer - increase from default 900 (15min)
 MINQUAL=50              ; Minimum quality to add nodes to the table
+;L2COMPRESS=1           ; Enable compression on L2 links
+;L2COMPMAXFRAME=3        ; Compress our MAXFRAME
 L4COMPRESS=1            ; Enable compression on L4 links
+;L4COMPMAXFRAME=3        ; Compress our MAXFRAME
 NODESINTERVAL=60        ; Broadcast / expect nodes every 60min
 OBSINIT=6               ; Initial OBS counter for an added node
@@ Line 61: / Line 67: @@
 ; INP3 Stuff
-MAXHOPS=3               ; Try to keep things limited, BDH sends a lot
+MAXHOPS=2               ; Try to keep things limited with such a high RTT
-MAXRTT=15               ; Fixed in BPQ 25.5
+MAXRTT=15               ; Fixed in 25.5
 PREFERINP3ROUTES=1      ;
 </code>
 **Routes**
 <code>
 ROUTES:
+GB7WOD,192,2
 ; Prioritise RDG on 2m
-GB7RDG,1,2,0,0,0,1
+;GB7RDG,1,2,0,0,0,1
-GB7RDG,1,6,0,0,0,1
+;GB7RDG,1,6,0,0,0,1
+GB7RDG,192,2,0,0,0,0
+GB7RDG,192,6,0,0,0,0
 ; Prioritise BDH on 2m
@@ Line 79: / Line 87: @@
 GB7BDH,1,6,0,0,0,1
+;M0MZF-1,1,7,0,0,0,1
+;M0MZF-1,1,6,0,0,0,1
 M0MZF-1,1,2,0,0,0,1
-G7BCS-7,192,2
-GB7WOD,192,2
+G7BCS-7,192,2,0,0,0,0
+;GB7BSK,192,2
+;MB7NPW,192,6
 ***
 </code>
 **RF Ports**
+<code>
 PORT
   PORTNUM=2
@@ Line 167: / Line 179: @@
   DIGIFLAG=0             ;Don't digipeat (=1 all, =255 UI only)
+  INP3ONLY=0             ;
   ENABLEINP3=1           ;Try INP3 when a link is established
   ALLOWINP3=1            ;Respond to INP3 on this port
@@ Line 182: / Line 195: @@
 From discussion on Discord:\\
-  * BPQ uses MAXRTT, round trip time
+<del>  * BPQ uses MAXRTT, round trip time</del>
   * BPQ sends full nodes table only when a neighbour first appears
   * BPQ sends RTT probes every 4 minutes and accumulates RTT from these