Differences

This shows you the differences between two versions of the page.

--- nodes:gb7win [2025/09/01 21:43] – [LinBPQ] m0mzf
+++ nodes:gb7win [2025/10/11 14:53] (current) – [Current and planned ports] m0mzf
@@ Line 19: / Line 19: @@
 |4| 70.4875MHz \\ 12.5KHz FM  | V Omni 0dBd 7mAGL   | - | -   | planned | | |
 |6| 50.650MHz \\ 12.5KHz FM  | V Omni 0dBd 40mAGL | 1011 QPSK 2k4 IL2P+CRC    | 13dBW 2.4KHz | active | [[nodes:gb7bdh|GB7BDH]] [[nodes:gb7rdg|GB7RDG]] |[[http://wessex.hopto.org:8070/|Wessex]] |
-|7| 432.650MHz \\ 25KHz FM  | V Omni 5dBd 7mAGL   | 0011 C4SK 9k6 IL2P+CRC | 14dBW 5KHz   | testing, low antenna | [[nodes:gb7sou|GB7SOU?]] | [[http://zepler-websdr.suws.org.uk/|SUWS]] |
+|7| 432.650MHz \\ 25KHz FM  | V Omni 5dBd 40mAGL   | 0010 GFSK 9k6 IL2P+CRC | 14dBW 5KHz   | testing | [[nodes:mb7npw|MB7NPW?]] | [[http://zepler-websdr.suws.org.uk/|SUWS]] |
 =====Coverage Maps=====
 Simulations from radiomobileonline; Outstation antenna 12m AGL; Strong signal 15dBuV/m, Weak Signal 3dBuV/m, Path "reliability" 95%
-^ 2m plot, 4dBi antenna^ 6m plot, 2.2dBi antenna^
+^ 2m plot ^ 6m plot ^
 | {{:nodes:2m_crab_wood_45m_25w_erp_base.png?400}} | {{:nodes:6m_crab_wood_45m_25w_erp_base.png?400}} |
+| Antenna 12m AGL, 4.4dBi omni \\ Rx threshold -3dBuV (S6) \\ Strong signal field 15.4dBuV/m \\ Weak signal field 3.4dBuV/m \\ Reliability 90% | Antenna 12m AGL, 2.2dBi omni \\ Rx threshold -3dBuV (S6) \\ Strong signal field 8.2dBuV/m \\ Weak signal field -3.8dBuV/m \\ Reliability 90% |
 =====Technical=====
 ====Hardware====
   * Modified Comet GP-15N @ ~40m AGL / ~200m ASL, 55m Andrews LDF7-50A
-  * Raspberry Pi 5 / Raspberry Pi OS (Debian Bookworm) / 256GB MLC NVMe SSD
+  * Raspberry Pi 5 (Debian Bookworm)
-  * Meanwell LRS-200-12 PSU
-  * GPIO Relays for remote power switching, Dallas 1-wire temperature sensor for radio
   * 70cm: Motorola GM360 (data in / flat audio out)
   * 2m: Motorola GM380 (data in / flat audio out)
   * 6m: Alinco DR-M06TH [[https://wiki.oarc.uk/radios:dr-m06th|(modulator / discriminator tapped)]]
-  * All ports use a NinoTNC A4 v3.42 firmware
+  * NinoTNC A4 v3.42 firmware
-  * [[https://wiki.oarc.uk/cm108_sound_interface_smd|CM108]] on NinoTNC RX audio tap for 1k2 AX.25 decode (Direwolf 1.7)
+  * [[https://wiki.oarc.uk/cm108_sound_interface_smd|CM108]] on NinoTNC RX audio tap for 1k2 AX.25 decode on 2m (Direwolf 1.7)
 ====LinBPQ====
 **Version**
-<code>G8BPQ AX25 Packet Switch System Version 6.0.24.82 August 2025 (hibbian)</code>
+<code>G8BPQ AX25 Packet Switch System Version 6.0.25.6 October 2025 (Test)</code>
 **Last updated**
-<code>Tue 2025-09-01 22:43:06 BST</code>
+<code>2025-09-10 10:24 BST</code>
 **Global**
 <code>
+; Set up some global  stuff
+; Set up some global  stuff
 ;T3=540                 ; L2 validation timer - increase from default 180 (3min)
 ;IDLETIME=2700          ; L2 idle link shutdown timer - increase from default 900 (15min)
 MINQUAL=50              ; Minimum quality to add nodes to the table
+;L2COMPRESS=1           ; Enable compression on L2 links
+;L2COMPMAXFRAME=3        ; Compress our MAXFRAME
 L4COMPRESS=1            ; Enable compression on L4 links
+;L4COMPMAXFRAME=3        ; Compress our MAXFRAME
 NODESINTERVAL=60        ; Broadcast / expect nodes every 60min
 OBSINIT=6               ; Initial OBS counter for an added node
@@ Line 57: / Line 63: @@
 L4DELAY=10              ; L4 delayed ACK timer
 L4RETRIES=6             ; L4 retry count, default=3, increased to 6
-L4TIMEOUT=120           ; L4 Timeout increased to 2min
+L4TIMEOUT=120           ; L4 Timeout 2min
 PACLEN=236              ; Max out NETROM frames
+; INP3 Stuff
+MAXHOPS=2               ; Try to keep things limited with such a high RTT
+MAXRTT=15               ; Fixed in 25.5
+PREFERINP3ROUTES=1      ;
 </code>
-<code>
 **Routes**
+<code>
 ROUTES:
 GB7WOD,192,2
-; Prioritise RDG on 6m
+; Prioritise RDG on 2m
-GB7RDG,192,6
+;GB7RDG,1,2,0,0,0,1
-GB7RDG,191,2
+;GB7RDG,1,6,0,0,0,1
+GB7RDG,192,2,0,0,0,0
+GB7RDG,192,6,0,0,0,0
 ; Prioritise BDH on 2m
-GB7BDH,192,2
+GB7BDH,1,2,0,0,0,1
-GB7BDH,191,6
+GB7BDH,1,6,0,0,0,1
-; Prioritise MZF on 70cm
+;M0MZF-1,1,7,0,0,0,1
-M0MZF-1,192,7
+;M0MZF-1,1,6,0,0,0,1
-M0MZF-1,191,2
+M0MZF-1,1,2,0,0,0,1
-G7BCS-7,192,2
+G7BCS-7,192,2,0,0,0,0
 ;GB7BSK,192,2
 ;MB7NPW,192,6
@@ Line 101: / Line 114: @@
   MAXFRAME=4             ;no., Default frames before ACK
   RESPTIME=648           ;msec, Delay before L2 ACK (256*8)/3600=568 +80msec
-  RETRIES=10             ;no., L2 retries before failure
+  RETRIES=10             ;no., L2 retries before failure, default=6
   SLOTTIME=100           ;msec, Wait time before checking PERSIST again
   PERSIST=255            ;255/(# hidden stations on link - 1) but we can hear everyone
   DIGIFLAG=0             ;Don't digipeat (=1 all, =255 UI only)
+  INP3ONLY=0             ;
+  ENABLEINP3=1           ;Try INP3 immediately when a link is established
+  ALLOWINP3=1            ;Respond to INP3 on this port
   QUALITY=1              ;Nodes heard on this port get this quality
   MINQUAL=50             ;Therefore do not broadcast nodes heard on this port
   NODESPACLEN=160        ;Keep NODES broadcast shorter to help decode
-;  QUALADJUST=100         ; % by which to reduce quality if the best neighbor is on the same port, needs tuning
   NONORMALIZE=1          ;Disable node quality normalisation algorithm
   IGNOREUNLOCKEDROUTES=1 ;Locked routes only
@@ Line 128: / Line 144: @@
   MAXFRAME=4             ;Default no. frames before ACK
   RESPTIME=933           ;msec, Delay time before L2 ACK (256*8)/2400=853 + 80msec
-  RETRIES=10             ;no., L2 retries before failure
+  RETRIES=10             ;no., L2 retries before failure, default=6
   SLOTTIME=100           ;msec, Wait time before checking PERSIST again
   PERSIST=255            ;255/(# hidden stations on link - 1) - but we can hear everyone
   DIGIFLAG=0             ;Don't digipeat (=1 all, =255 UI only)
+  INP3ONLY=0             ;
+  ENABLEINP3=1           ;Try INP3 immediately when a link is established
+  ALLOWINP3=1            ;Respond to INP3 on this port
   QUALITY=1              ;Nodes heard on this port get this quality
   MINQUAL=50             ;Therefore do not broadcast nodes heard on this port
   NODESPACLEN=160        ;Keep NODES broadcast shorter to help decode
-;  QUALADJUST=100         ; % by which to reduce quality if the best neighbor is on the same port, needs tuning
   NONORMALIZE=1          ;Disable node quality normalisation algorithm
   IGNOREUNLOCKEDROUTES=1 ;Locked routes only
@@ Line 149: / Line 168: @@
   COMPORT=/dev/tnc-70cm
   SPEED=57600
-  TXDELAY=40             ;msec, GM340 keys up fast
+  TXDELAY=100             ;msec, GM340 keys up fast
   TXTAIL=1               ;msec, Needed to prevent NinoTNC sending 30msec tail
   FRACK=4000             ;msec, Needs tuning
@@ Line 155: / Line 174: @@
   MAXFRAME=8             ;Default no. frames before ACK
   RESPTIME=213           ;msec, Delay time before L2 ACK (256*8)/9600=213
-  RETRIES=10             ;no., L2 retries before failure
+  RETRIES=10             ;no., L2 retries before failure, default=6
   SLOTTIME=20            ;msec, Wait time before checking PERSIST again
   PERSIST=255            ;255/(# hidden stations on link - 1) - but we can hear everyone
   DIGIFLAG=0             ;Don't digipeat (=1 all, =255 UI only)
+  INP3ONLY=0             ;
+  ENABLEINP3=1           ;Try INP3 when a link is established
+  ALLOWINP3=1            ;Respond to INP3 on this port
   QUALITY=1              ;Nodes heard on this port get this quality
   MINQUAL=50             ;Therefore do not broadcast nodes heard on this port
   NODESPACLEN=160        ;Keep NODES broadcast shorter to help decode
-;  QUALADJUST=100         ; % by which to reduce quality if the best neighbor is on the same port, needs tuning
   NONORMALIZE=1          ;Disable node quality normalisation algorithm
   IGNOREUNLOCKEDROUTES=1 ;Locked routes only
@@ Line 171: / Line 193: @@
 Testing INP3 in the local area; GB7BDH, M1BFP, GB7BSK, MB7NPW, GB7RDG, GB7WIN\\
 Maybe GB7WOD? GB7WOK? GB7BRK? G7BCS?
-MAXRTT=90 seems a bit high?\\
-MAXHOPS=5 is probably a minimum?\\
-Plan is to document this "better" over on the OARC Wiki but for posterity...
 From discussion on Discord:\\
-  * BPQ uses MAXRTT, round trip time
+<del>  * BPQ uses MAXRTT, round trip time</del>
   * BPQ sends full nodes table only when a neighbour first appears
   * BPQ sends RTT probes every 4 minutes and accumulates RTT from these
@@ Line 192: / Line 209: @@
   * XRouter resets OBSCNT after receiving a NODES table from neighbour
   * XRouter sends a node drop immediately
-====LinBPQ====
-**Version**
-<code>G8BPQ AX25 Packet Switch System Version 6.0.24.69 March 2025 (G8BPQ beta)</code>
-**Last updated**
-<code>Mon 2025-04-121 22:16:14 BST</code>
-**Global**
-<code>
-;T3=540                 ; L2 validation timer - increase from default 180 (3min)
-;IDLETIME=2700          ; L2 idle link shutdown timer - increase from default 900 (15min)
-MINQUAL=50              ; Minimum quality to add nodes to the table
-L4COMPRESS=1            ; Enable compression on L4 links
-NODESINTERVAL=60        ; Broadcast / expect nodes every 60min
-OBSINIT=6               ; Initial OBS counter for an added node
-OBSMIN=4                ; Minimum OBS number to select broadcasted nodes
-L3TIMETOLIVE=25         ; L3 maximum hops count
-L4DELAY=10              ; L4 delayed ACK timer
-L4RETRIES=6             ; L4 retry count, default=3, increased to 6
-L4TIMEOUT=120           ; L4 Timeout increased to 2min
-PACLEN=236              ; Max out NETROM frames
-</code>
-**Routes**
-<code>
-ROUTES:				; Locked routes (31 maximum)
-; CALLSIGN,QUALITY,PORT[,MAXFRAME,FRACK,PACLEN,INP3Flag]
-GB7BDH,1,2,8,7000,236,1         ;Good to BDH on 2, intermittent on 6
-GB7BDH,1,6,2,4000,160,1         ;Keep PACLEN lower on 6m
-GB7RDG,1,2,8,7000,236,1         ;Good to RDG on 2, intermittent on 6
-GB7RDG,1,6,2,4000,160,1         ;Keep PACLEN lower on 6
-GB7BSK,1,2,8,7000,236,1         ;Good-ish to BSK on 2
-MB7NPW,1,2,8,4000,120,1         ;Intermittent to NPW on 2, PACLEN low, try it out?
-M0MZF-1,1,2,8,7000,236,1        ;Good paths to Sysops
-G8IPG-1,1,2,8,7000,236,1
-***
-</code>
-**RF Ports**
-<code>
-PORT
-  PORTNUM=2
-  ID=144.9375MHz/Nino-0101/QPSK/3k6
-  M0LTEMapInfo=RF,144.9375,QPSK,3600,3600,Mixed
-  TYPE=ASYNC
-  PROTOCOL=KISS
-  KISSOPTIONS=ACKMODE
-  COMPORT=/dev/tnc-2m
-  SPEED=57600
-  TXDELAY=100            ;msec, Seems OK for a relay-switched 857d
-  TXTAIL=1               ;msec, Needed to prevent NinoTNC sending 30msec tail
-  FRACK=7000             ;msec, Busy channel, 7sec ACK timeout
-  PACLEN=236             ;bytes, 236 is max for a NETROM frame
-  MAXFRAME=4             ;no., Default frames before ACK
-  RESPTIME=600           ;msec, Delay time before L2 ACK (256*8)/3600=568
-  SLOTTIME=100           ;msec, Wait time before checking PERSIST again
-  PERSIST=51             ;255/(# hidden stations on link - 1) but we can hear everyone
-  DIGIFLAG=0             ;Don't digipeat (=1 all, =255 UI only)
-;INP3 tunables
-  IGNOREUNLOCKEDROUTES=0 ;Peer to all
-  QUALITY=0              ;Disable quality based routing
-  INP3ONLY=1             ;Enable INP3 Only
-  MAXRTT=90              ;sec, Max RTT to add INP3 node
-  MAXHOPS=5              ;num, Max distance to other INP3 node
-ENDPORT
-PORT
-  PORTNUM=6
-  ID=50.650MHz/Nino-1011/BPSK/2k4
-  M0LTEMapInfo=RF,50.650,QPSK,2400,2400,Backbone
-  TYPE=ASYNC
-  PROTOCOL=KISS
-  KISSOPTIONS=ACKMODE
-  COMPORT=/dev/tnc-6m
-  SPEED=57600
-  TXDELAY=180            ;msec, DR-M06 takes ~150msec to key up
-  TXTAIL=1               ;msec, Needed to prevent NinoTNC sending 30msec tail
-  FRACK=4000             ;msec, Needs tuning
-  PACLEN=160             ;bytes, 236 is max for a NETROM frame
-  MAXFRAME=4             ;Default no. frames before ACK
-  RESPTIME=900           ;msec, Delay time before L2 ACK (256*8)/2400=853
-  SLOTTIME=100           ;msec, Wait time before checking PERSIST again
-  PERSIST=255            ;255/(# hidden stations on link - 1) - but we can hear everyone
-  DIGIFLAG=0             ;Don't digipeat (=1 all, =255 UI only)
-;INP3 tunables
-  IGNOREUNLOCKEDROUTES=0 ;Peer to all
-  QUALITY=0              ;Disable quality based routing
-  INP3ONLY=1             ;Enable INP3 Only
-  MAXRTT=90              ;sec, Max RTT to add INP3 node
-  MAXHOPS=5              ;num, Max distance to other INP3 node
-ENDPORT
-</code>
 =====Other FAC'd equipment on site=====